Is there any applications written for funcube dongle in visual basic and there the source code is open? I am lazy and does not want to invent the wheel again ...
Following from my initial success with Gqrx, and then problems caused by audio overrun in Ubuntu 11.10 I installed Kubuntu 11.10 in a separate partition on my...
Folks Release 18j available here: http://www.funcubedongle.com/MyImages/export18j.pro.bin This has a fix for the incorrect filter preselection between 868MHz...
Folks As promised, I have some new firmware to tackle the click problem. http://www.funcubedongle.com/MyImages/export18i.pro.bin It's taken some time, mostly...
Alex, and the rest of the group, you may be pleased to hear that I've successfully built *Gqrx* (and GNU Radio 3.4.2) from source under *Ubuntu 11.04*, and...
Hello, My apologies for taking so long to get this project out. It really was vaporware for a while. I'll be checking in here to offer support. Its free,...
Here's a link to a video demo of software I developed in Max/MSP that runs with the FCD pro on a Macbook. I'm writing up documentation, etc., over next week,...
Surrey Satellite Technology (SSTL) and the Surrey Space Centre (SSC) at the University of Surrey today announced the four lucky winners of the `Space App...
Hi All, I would like to know if the FCD firmware source code is public and available. I started a tiny project with a Pic32 for setup a remote receiver and I'm...
For when you have nothing to do... 1) Swap IQ via a command to the dongle 2) Add in a few 32-bit memories, I would like to save the calibration info...
Hello, I try to cross compile Alexandryu's gnuradio block for FCD for ARM processor. The development system is Linux/64 on Intel processor, I use Open Embedded...
Happened across this software following a link from Hackaday http://wiki.radioreference.com/index.php/Digital_Speech_Decoder_%28software_package%29 Might be of...
Hi All Developers, Most if not all users of my program have to select an option to swap over I+Q (swaps L+R channels) compares the the standard SoftRock...
Hi, I'm trying to install/run Qthid on a macbook (osx 10.6) Inside the qthid-3.0 folder (from the .dmg), if I click on the file Qthid the message: You can't...
FCHid.exe returns the following when setting frequency HIDOpen of Vid_04d8&Pid_fb56 return:1 Success FCD found HID ReadCommand returns:0 Error FCD read command...
Not sure if anyone else is having this, but when I set the LNA gain at +25.0dB or +30db it's reducing the signal? the rest are fine, just the last two on the...
I'm now testing build 764 where I've fixed a lot of bugs, added features etc. After I've done some paperwork, taken to pooch for a prowl and had a beer I'll...
Simon at some point in your busy schedule, would it be possible to add positive feedback for your HRD rotator control with the DCU-1 protocol, (AI1 comamnd...
Hi Mike, I noticed that the about-box of the ExtIO_FCD_G0MJW.dll version 0.5.1.1 still shows "FCD Control V0.4". This might be confusing to some of the users,...
Curious minds would like to be educated J Why not put an option into the Firmware to drop the audio level? All-in-all this would be easier for Windows and...
If anyone out there in developer land would like a DLL incl. source with what IMO is full Doppler support then just say so. This is a DLL I developed years ago...
Hi Strange error I have. GQRX says I should use hw:0 to start. hw: 0 (= no sound) if I try to hw:1 the program don not start. arecord -l .. card 2: default...
Hi, Very early days here, I see that noise from the Dongle with no antenna is ~ 40dB higher than any of my soundcards, this is irrespective of whether I open...
