Hello all, I'm currently working on the wheels for my KS600...though I'm going to use them for the time being, I'll probably look to invest in a new set at...
Not sure where you're located. One place folks talk a lot about in the States is Buchanans: http://www.buchananspokes.com ... Paul S. Greenberg Optical...
Hi Mike I have the Vech kit, it is well made and came with a Fram PH6607 filter with the flow disabled, Vech seems to have done this by simply drilling or with...
Ian Peachey
ipeachey@...
Nov 2, 2004 9:54 am
5632
More problems. Hi all Having got my engine ready to go back together I have once again come up against a problem. I have had new follower guides made from...
Ian Peachey
ipeachey@...
Nov 2, 2004 10:30 am
5633
Ian, I sit possible to see a seperate pic of both sides of the round plate and of the hexagon head bolt which has come in Vech's adaptor. regards Nigel ... ...
Hi Ian, How did he manage to cast this cover? Did he have a sample? Looks good too. Perhaps you could try putting a thick gasket between this cover and the...
Heck Paul U, I erred. "A" is the breathervalve it rotates with the camshaft. "B" is where "A" fits in. "A" has two holes, and when they match with the tube in...
Hi Nigel Yes he did have a sample he has an R12 in need of a rebuild condition, so the mold came from his. The gasket will not work because the binding is not...
Ian Peachey
ipeachey@...
Nov 2, 2004 2:46 pm
5638
Hallo Ian, I can´t do much about your problem for the known limitations during week. I can´t even get your pictures from office and it is only a matter of...
Hi Ian, Is the binding so bad. Can you not tighten the cover a bit and then rotate the engine with the chains on so as to have the cam shaft and "A" rotate in...
On Tuesday 02 Nov 2004 10:31, Ian Peachey wrote :- ... Ian The problem here lies in the machining of the part and not in the casting. What has happened is that...
Thanks Nigel I had not thought of that. I will see also if I can get my hands on any of that engineers bluing that may help highlight it. Thanks again for a...
Ian Peachey
ipeachey@...
Nov 2, 2004 5:32 pm
5642
Thanks Drew You are right I am sure, like you said you would use cheese head screws (I am) but this is also part of the problem, the cheese heads tend to pull...
Ian Peachey
ipeachey@...
Nov 2, 2004 5:49 pm
5643
Ian You can borrow mine if it helps-it is original and might be useful for checking dimensions. This sounds like your problem. Alternatively, I can do that if...
On Tuesday 02 Nov 2004 17:50, Ian Peachey wrote :- ... Ian I think you may have misunderstood my meaning here. First by "cheesehead" I mean a screw with a drum...
Hmmmmm.. like the PCV's in modern vehicles. Only yesterday i was thinking of this... maybe onto the end of the breather tube. Because if that oricinal breather...
... It ends when you sell it. Until then you don't really own it, you are merely renting it long term. I know what I'm talking about. I have 15 of these...
G' Day one and all need some help please....There was a link posted some time ago for bosch magneto spares ...I think it was in Germany.....does anyone still...
Hi Drew Sorry yes I did misunderstand you are right reg' the cheese heads this will work quite well. I would have to get this centered and correct with the top...
Ian Peachey
ipeachey@...
Nov 4, 2004 12:14 pm
5653
Hi Peter You need to speak to/contact Mr H Schmidt or Mr U Doderlein BMZ (BAYERISCHE MAGNET ZUNDER) Ringstase 4 85254 Othofen Phone 0049-8283-99890 Fax...
Ian Peachey
ipeachey@...
Nov 4, 2004 12:16 pm
5654
I just correct details: BMZ (BAYERISCHE MAGNETZÜNDER) Ringstrasse 4 85254 Osthofen Phone 0049-8283-99890 Fax 08134/7693 Mail bmz.magnetos(at)t-online.de Web...
Hi Peter, I am slso doing an R42, I am looking for a front fender. I have bought some parts from Dreher which were fine, expensive but good.Do you know of any...
Can't seem to get out the gate. Back when I mentioned this there was a prob with the cc not matching the billing address. Got that fixed but the cell phone...
