Thanks for the tip on removing the crank pulley. I've been giving the car a thorough check & when i unclipped the flywheel/alternator wiring, one of the three...
Hi Paul It is doubtful the yellow wires are the cause but join them up again anyway, you may also have a charging problem that you are unaware of as well! To...
Hi everyone, i have just replaced the nearside front wheel bearings on my Aixam 500 diesel and need to know how much torque to put on the drive shaft nut to...
Ian where did you source the front wheel bearings from? Mine are making a bit of a din, especially the left. Tim ... From: ian.bugden <ian.bugden@...> ...
Has anybody had the same misshap as i had with drive belt on Axiam A 750 which broke clean in two after only 11500 odd miles it had a clean cut strate...
Hi Tim, havent got the bearing, yet just extracted it.I am going to take the old one to a local specialist bearing manufacturer/stockist (Ashley Power) and see...
Hi guys, a bearing specialist should be able to supply, I've got a pair on standby - SKF BAHB633313EA I haven't found a torque setting yet though :o( JJ. Those...
bang went the belt can anyone one tell me where i can get a drive belt other than berrybrook? or does anyone have a part number I can order from my local...
Thanks kubotabuddy I've just tested the hall sensor, The values are as follows when putting the meter across the black & red wires it does read 12v, then when...
Sorry to say Paul but my money is on the hall effect switch, if you are not seeing two changes of voltage per rotation, then the optic lens is not in a...
www.graysofthrapston.co.uk Can order off the net, pretty quick delivery too. Under £25 if I remember right I ordered X2 so I always have a spare in the boot ...
Hi Tim, have tried local bearing stockist without much luck, but Grays of Thrapston have now put them on there on line shop priced at £19.18 plus vat. To...
Hi I had a look at my front wheel bearings last week & they do need changing. Just a thank you to the group for the front wheel bearing information. Clay From:...
Hi Tim. Had to do the front bearings on our 500 Mac which gets driven year round. When investigating how to, we discovered that, like motorcycles, the...
I will be out of the office starting 06/06/2008 and will not return until 09/06/2008. Hi I am away from the office now until Monday June 9th with no access to...
agupwell@...
Jun 6, 2008 3:33 pm
4372
wondering if anyone can help, my ligier ambra has a issue with both doors whereas if you close em normally they wont shut, you have to actually lift the door...
Ive no experience with the car you have but "normal" cars often have pins that go through the hinges, they are made so they snap if the door is over opened....
Hi Lisa, have you had a look at the top hinges to see if they've become lose. If you do decide to add some more plates to the bottom hinges you might have to...
hi, none of the hinges seem to be particularly loose, hence why i thought added more plates might help the situation, as far as i can tell if i can get the...
Hi Lisa Best way of lifting the doors is to loosen both the hindge bolts, put a jack under the door frame at the bottom centre, making sure to protect the...
Lisa, Does the door sit right in the opening? It might be that the hinges are fine, but the striker plate is out of adjustment at the lock end of the door,...
hi its actually kinda hard to tell, when the doors are open they seem to be fine, but as soon as try to close em they arent having it! its the same for both...
... Hi Greg Strange you should mention Exeter :) I can tell you where to get the items I've replaced on my car, but there isn't a specific dealer as far as I...
Hi folks, I have just replaced my 2002 Aixam gearbox bearings; the box was in good order but the input bearing was starting to make some noise if the pulley...
HI ALL iv just got a gs,moon buggy fitted with a the 500 twin diesel rngine and as far as i can see it a AIXAM engine had good pulling away power but top speed...
