Hi All Im not a Aixam owner yet but I went to see a Aixam 500 Evolution a few days ago and was really impressed, ok it was dark and I didnt actually have a...
There isn't a manual, just what us lot have discovered scattered about the net, have a look at the files bit. Yes mines on 81,000 miles, and as for flogging...
I can only speak as a former Ligier owner, which used the same engine gearbox drive train etc but with a different bodystyle and some would argue in a more...
Hi,Having had quite a few Aixam's myself now, plus having one at the mo, I can safely say if there's am alternative take it. I can't speak for the Microcar's...
Hi (Daz?) I love mine and wouldn't hesitate to drive it regularly if I had to. They're a specialist interest though, the diesels are noisy and 50mph difficult...
Hi Daz, I think you will find a dealer for Microcar and one for Aixam in Wem Shropshire, I had the older Aixam 500 but now a Microcar MGO owner. I've looked at...
An Aixam isn't a "normal" car. but taken within its limitations, it passes for transport. As a former BMWR80 outfit driver i find it comfortable and...
Where do you fill up and check the oil level in the gearbox on a 2008 mc2 microcar highland,I'm buggered if I can see where you do it,also is there a workshop...
Hi jem - Firstly the carpets often get damp underneath which promotes misting - poor sealing under them, around the lower rear door seal edges and even where...
Hi JJ Blimey! something to look out for and typical of the "hope for the best" style of engineering design on these things. My water leak problem (in 2007) was...
my microcar mc1-working fine one day next morning turn on ignition and absolutely nothing no lights/horn wont turn engine ,have changed battery -old one dead...
I was getting a bad judder when pulling away from a stand still in my Aixam Crossline.It started not long after I changed the belt and the pulleys wearing...
Hi, I have a Aixam 500 .year 2001,engine Kubota Z482 and I have some problems ,and no one can help me and I think you can help me. One month ago I changed the...
Yes--Your belt is too slack.... --Bet it wont start running up a very steep hill either! Set the rear pulley so that the belt has around 1/2-1" deflection when...
How tight is the belt when not running? Should be around 1/2-1" slack when pressed with finger. Maybe when bracket broke and you welded it, its slightly...
Hi Riitey, I seem to have missed this one. I don't have a MC2 but going by the MC1 picture I have seen there is a vent plug up the right side near the top, a...
Hi Alex very sorry to hear of your trouble. My car has not eaten belts like that, if it did I would check that the rear pulley and the front pulley are lined...
Hiya Jenny. Useing WD40 just lubricates the weights in the dome section, these sometimes get stuck or are sluggish to move, its done on a regular basis at some...
... When I welded the bracket ...i welded perfect...there is no room for errors.... I use this belt because in Romania the orignal belt IBC(Aixam) is very...
... Hi JJ, Today I get out the gearbox and the rear pulley.Tomorrow i will watch in the gearbox if all is in the place.... My pulley have two washer(i think is...
Hi Alex. Did you go and see the picture? It shows how you can put a straight piece of something on the pulley edge to tell if both the pulleys are in the right...
Hi had the same problem had the bushes replaced by engneering works for bronze grafite lasted 450 miles and packed up destroying the new belt. I think the...
Hi Alex. The gearbox is made straight by the mounting plates to the engine. There is no adjustment, so something must be broken or missing, or in the wrong...
... JJ you are the man !Thank you very very much for help.I found the problem ! ! ! Last summer the engine mounting(in back of gearbox has broked).I used the...
http://www.flickr.com/photos/29179705@N02/6581463155/ Hi Alex. This is the best picture I can get. I can not measure the spacer. It looks about 10mm thick. I...
