mazda626uk : Messages : 1294-1324 of 2676

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

1294	I am going to have a go at the timing belt next weekend. Looking into the engine bay from the front of the car, which is No 1 cylinder? Paul...	paulbrears2000	Jul 2, 2005 6:00 pm
1295	if its the v6 then its (1) back left, (2) front left, (3) middle back, (4) middle front, (5) back right, (6) front right paulbrears2000...	Henry State fraserbanks2000	Jul 2, 2005 7:33 pm
1296	Hi Paul, On your 2.0 I4, no1 cylinder is on the left, nearest the belt.. Have you got the details on the belt change, or do you want me to email them? John...	John compyshop	Jul 2, 2005 9:18 pm
1297	Thanx for the info Guys, Its ok re the belt change details John, someone with a copy of Data disc has given them to me,Although the stated time of 1.7 hours...	paul paulbrears2000	Jul 3, 2005 9:22 am
1298	Let us know how you get on with it Paul.. John...	John compyshop	Jul 3, 2005 10:30 am
1299	Hi Paul Which year is your car? What's the mileage? Are you planning on adjusting the engine valve clearances as well? Are you going to change the water pump...	sbetts992003	Jul 3, 2005 5:48 pm
1300	Hi everyone, This applies to all vehicles and not just the Mazda range. Which of the following 2 methods of driving uses more fuel:- A) If i'm in 5th gear and...	sbetts992003	Jul 3, 2005 5:57 pm
1301	Hi, Got to be B. G sbetts992003 <sbetts99@...> wrote: Hi everyone, This applies to all vehicles and not just the Mazda range. Which of the following 2...	glenn m mosquitos_uk	Jul 3, 2005 6:00 pm
1302	The valve clearances use HLA's so no adjustment needed... Water pump is a good idea, just to save on the labour of doing it later... John...	John compyshop	Jul 3, 2005 6:05 pm
1303	It will be B.. but it is illegal, as aparently, you are not in full control of the car, and are relying on just the brakes to slow down... John...	John compyshop	Jul 3, 2005 6:09 pm
1304	Its a 1995 626 2Ltr 120,000 on the clock, duno about the water pump yet, I recon if I can manage the timing belt then any problems with the water pump I can...	paul paulbrears2000	Jul 3, 2005 7:09 pm
1305	The water pump was taking your advice John from one of your earlier posts - very useful. The engine valve clearances - there is a lot of confusion (in my mind ...	sbetts992003	Jul 3, 2005 7:26 pm
1306	Doing the shims is best left to the dealers, as they will have a bucket full, and just swap those that are needed... the shims themselves do not wear, so you...	John compyshop	Jul 3, 2005 9:59 pm
1307	I recharged the gas system today and now it's cooling superb! It was almost empty. The noise from the compressor also went away... Johnny ... From: "John"...	Johnny Holdhus huskyno	Jul 8, 2005 8:04 pm
1308	That's great Johnny, glad to hear it.. And thanks for letting us know. John...	John compyshop	Jul 8, 2005 8:19 pm
1309	My instrament panel lights aren't working, I've checked and if they get a good ground and power, they work fine, but for some reason they won't even turn on...	kyle_oakeson	Jul 9, 2005 4:25 pm
1310	Hi Kyle, and welcome to the club... I only have the diagrams for the later models.. although, I think you only need to check the fuses... If you have a...	John compyshop	Jul 9, 2005 8:07 pm
1311	Hey John, The Instrament panel doesn't get full power for some reason, a little more than 10v, and the dimmer switch seams to only get half that (the plug tha...	Kyle Oakeson kyle_oakeson	Jul 9, 2005 9:02 pm
1312	Sounds like faulty wiring... poor earth, short or something like that... dont worry about the extra plugs.. that's normal.... it's cheaper to make one harness...	John compyshop	Jul 9, 2005 11:51 pm
1313	Hi there, problem is poor/uneven/jerky acceleration at low revs, up to 2000rpm. Above is ok. Seems like clogged injectors. What is the medicine to use? High...	karosas0	Jul 12, 2005 11:34 am
1314	I have had similar problems with my 98 626 2.0 estate A bottle of STP injector cleaner helped a little, But the problem was my plugs were absolutley knackered....	jimbob_ukhub	Jul 12, 2005 12:17 pm
1315	Just to add.. Have a look round and see if any pipes have come off... Clean the inside of the dizzy cap and rotor arm.. John...	John compyshop	Jul 12, 2005 5:16 pm
1316	Please help! Need at least some partial wiring diagram for 626 GD '90 with A/C components integrated into the whole system. Doing the upgrade on Ford Probe...	wrzosekp	Jul 18, 2005 10:32 am
1317	Hi Pawel, You might be disappointed because there is no Probe equivalent for the GD 626... only the GE was the same.. even then, I expect some slight ...	John compyshop	Jul 18, 2005 4:50 pm
1318	i have this problem on my right-rear brake (which is a disc brake), and the recommended solution is replace the caliper assembly. unfortunately a new caliper...	Orlando Andico orly_andico	Jul 20, 2005 2:41 am
1319	Hi Orlando, You can free it off, strip it down, and use a copper based grease on the pivot... this will work for a long time if done regularly, I know people...	John compyshop	Jul 20, 2005 7:32 am
1320	could you email me the belt change details? i've a '97 dohc-4cyl (manual) and though its my 4th 626, have never done this, though close to everything else!...	brownplus	Jul 21, 2005 9:37 pm
1321	Hi Brownplus, and welcome to the club.. I have emailed you the details.. they are for models upto 97 (GE) but should be near enough, if you have the later (GF)...	John compyshop	Jul 21, 2005 9:59 pm
1323	Thank You John, I was expecting difficulties so I laboured through the internet to find what looks to be the thing: maz-ewd.pdf (1.5 M), a tutorial for car ...	wrzosekp	Jul 22, 2005 8:39 am
1324	thanks guys, it's funny but true?...I find the brits much more "serious?" and in the know about important (keep it running well) diy stuff online, and yanks...	brownplus	Jul 23, 2005 3:27 am

Yahoo! Groups Tips

Did you know...

Messages