Glad to hear you have fixed it. A lot cheaper too than buying a new igniter module. Cheers, Nicholas ________________________________ From: Jonathan Wilbour...
Hi Andrew, I have a 94 MX-3 V6 silve and love mine. I bought parts from ebay and the shipping cost wasn't too bad so recomend you shop around. Best wishes, ...
Hi Andrew, and welcome to the club.. Gas Struts... way too expensive from the dealers, and to be honest, they will fail after a few years anyway.. I got mine...
Hi i'm new to this group, I have a 1996 Silver Mazda 626 1.8 lxi, I love the car but im in search of a few parts and I can't seem to find any in my locar...
Thanks guys, the wire between the ignition module "C" terminal and the coil's "-" end was broken. Now the car running well. Thanks again for your help! Will ...
... Weeeeeeeell, today at around 12:45, I had this sudden bout of clarity.............This car has a manual trans axel hasn't it? So, without further ado I got...
Hello Will, That model 626 sounds like the 1989 626 2.2L one I had in Canada many years ago. I had the same problem, just before I sold the car. It was the...
I only have them for the 92-97 range... I will presume they are going to be completely different.. Very basically, one wire is a 12V feed from the ignition...
Hi, does anybody have a wiring diagram for the ignition system? No spark, I already replaced the coil and the ignition module, now i try to check the wiring,...
... Hi John. The car refuses to play the game with me and make the noise when static! Still, it goes away when the car is heated up. I also removed the...
Usual one would be the clutch release bearing, but it's normally a rumbling or screeching noise.. It's pretty hard to describe a noise, and even harder to...
Hello nice people. I have got what I can only describe as a "funny noise" a bit like a plastic fan rubbing on the radiator? But, coming from, I think, the...
The head doesn't normally get damaged... it is usually a number of valves, and possibly pistons that become damaged due to contact. On most engines, damage...
The above packed up within my car 626 GXi 2lit 1998 'S' Reg. I had new timing kit fitted. The car runs OK. What I want to know is does anyone out there know if...
Hi Terry. The PCV valve is on top of the rocker cover, at the rear.. has a 90deg bend and has a rubber pipe going to it.. it will just pull out. If you shake...
MANY THANKS FOR YOUR HELP SORRY NOT BEEN ON HERE MUCH JUST SEEN THAT YOU SENT ME EMAIL AS WELL I JUST CHECKED MY EMAIL AND 3298 EMAILS TO GO THROUGH BUT THIS...
... WElcome to my "idle problems" camp, Terry! Seeing that your car is so much younger than mine, the engine controls are presumably diffrent. On your car too...
i have mazda 626 on x plate year 2000 i need to find out about 2 things first is the tick over is very lumpy and seems to drive ok thou just seems to be miss...
Dear John, as I pointed this out, the car was only once at a dealer in its12 years of life (I having done every other service and repair on it). Then it was...
Hi Nicholas, Glad you have found the problem.. It is unlikely to have been like that at manufacture, and is more likely to have been a repair in the past which...
John, I spent ages looking for air leak, but found none. But I did find this below, which ahs to be a first: I seem to have cured the idle problem. The...
Hello There! I seem to have cured the idle problem. The solution has been too simple to contemplate. Some 3 weeks ago i first noticed that there is a rubber...
Hi Kev.. Well to be honest, most problems of this nature are down to a small air leak.. either from cracked rubber pipes, loose or disconnected pipes, or leaks...
hi, I had similar problems with a rough idle when the car had warmed up. i replaced the air intake manifold gasket and the problem was solved. i have a 2000 gf...
