You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
In the UK, all you need is to go to a garage that will give a certificate of roadworthiness.. it's just a glorified MOT. (MOT: a compulsory yearly inspection...
Hi, The dashboard fuse of my 94 626/2.0/L4 was blown when I tried to obtain OBD-I trouble code. I followed the drawing in Haynes Repair Manual and used a...
Recently, when I accelerate my car, I can hear loud water flow noise underneath the dashboard in the A/Cs cooling coil area. It's only happen when I...
The engine codes are shown be shorting the GND and TEN terminals ABS codes are TBS and GND You need to connect an LED with a resistor to the FEN and B+...
Are the crankshaft pulleys on V6 engines the two piece type, sometimes called a harmonic balancer? I have a squeak that has turned into a rattle in the pulley...
Crankshaft pulley is one piece.. My advice is to remove the pulley belts, one at a time. if the noise disappears, you will find your problem. more than likely...
Description of the problem: My car is a MAZDA 626 1.8 Liter Hatchback , model 1997 When the engine is cold and when I start the engine, the accelerator remains...
Best advice? Change dealers, and quick. But not before you you have been back to this incompetent dealer, armed with all your receipts, and whispered "trading...
I would agree with Bournemouth there... If it's something you can't live with, then take it back and have them fix it.. it sounds like they caused the problem....
They changed the model in 91.. is it a GD or GE? GE is same as MX6, possibly Probe too. A new caliper is about £100. even more from dealers. GD is older shape...
Hope I did this Right! Bought myself a 97 mx6 with 39000 on the clock. Had the cambelt and tensioner changed just in case any maintenance advise would be...
normally 60000 for cambelt, at least you know it's been done now. change the oil and filter very regular, thats about the only thing that kills these engines....
Thanks for your prompt reply. I am leaving in France , and unfortunately there are not a lot of MAZDA FR dealers . My usual dealer (the uncompetent one) is the...
... at ... Thanks for the advice about the oil type. The Mazda dealer at Newport Gwent suggested the belt change as they say they like to change it at 5 years...
John, Thank you for the information. I did the OBD code reading following the procedure. The Check Engine Light was on but did not flash out the codes. I also...
does the car run OK? it may be normal for the CEL to come on and then go off.. UK models don't have a CEL. it is also possible that you may have damaged the...
The car does have some problems. It will not speed up when I press the pedal normally after stopping at a traffic light. I have to press it very gentlely or...
I presume it is an automatic... Where are you based? (country) is it an import? Maybe a tranny problem.. (hold light flashing?) need full info. will check in...
It is a 94 626 2.0/I4 94,500 miles with automatic transmission. I am in US. The car was made in the US Mazda factory. The hold light is not flashing. (I...
Just got my new website uploaded. It's a Xedos site, or will be when I get the rest of it onto the server, but if anybody would like to send in some pictures...
So the car, engine wise seems ok.. but the transmission is slipping. you need to go to a transmission speciallist. I'm afraid this will be expensive to repair....
Hey all. I haven't posted here in awhile(been too busy with work, etc) but I've got a question that you all can probably help me with! I've just tossed out my...
Hi Pete, UK spec models have the same design.. dipped beam/full beam and a separate full beam. As you say, they should work as one dipped or both on full. I...
... Thanks for the reply! I checked the harness for any dirt and anything else that would cause potential problems and I cleaned the harness and the...
Is it the dipped beam that is dim, or is it the Sidelights (markers or whatever you call them over there, about a 4w bulb) You could also measure the voltage. ...
... before. ... It's not the sidelights, it's the low beams that dim when I switch the main beams on. The wiring plugged in as normal on the H4 low beams, but...
