Hi John / Dave, Finally i got the head gasket changed. I also changing the valve seals & performing valve grinding & block grinding. OK, I would like to reset...
OK, I would like to reset the ignition timing, how to do that? I have ignition flash light, by shorting terminal TEN to GRD, I can start to adjust the...
Hi John, ... Hi Xavier, glad you have the head sorted now.. You are correct in the fact that you have to short out the TEN and GND terminals in the diagnostic...
... step for 1 degree? ... timing? (silly question) ... It looks like 2 degrees for each line... as 10 degrees is before TDC.. further anticlockwise ( 11,12...
Hi John, Damn, the mechanic has adjusted the TPS & the nut stopper for the throttle head, the rpm ran off to 1,000rpm with A/C off & 800rpm with A/C switch on....
Hi xavier.. No bull.... you are in trouble :( But I think I can help... :) first, you need to set the thottle stop screw correctly.. ie the butterfly should...
Hi all, i've got a '90 626 GD with the 2l 12v engine and just wondered what the idle speed with choke is, mine is usually around 2000rpm so wondered if this is...
Hi Liam, and welcome to the club.. Yes, the idle speed when starting from cold should be between 2000 and 2500rpm.. I know it sounds high, but that is correct....
Thanks John, my 626 is in good working condition right now. I managed to set it to 700rpm (A/C Off) & 800rpm (A/C On). BR, Xavier No bull.... you are in...
hi john, thanks for the reply, always nice to know that the cars all fine! after years of owning fords i finally lost my temper with them and thought i'd try a...
I picked up a used 1995 MX-6 and all accessories, manuals, wheel lock keys etc have been tossed out, probablly by a detailer. The car might have had a keyless...
Hi Lee and welcome to the club.. The remote locking is part of the alarm system (if fitted)and is underneath the dashboard on the passenger side.. there are a...
That sounds very cool! I've never heard of that option before but I like it. Thanks also for the info, I'll have to go on an under-dash expedition to see if I...
Hi, Im new here how are you. I am looking to get a sensible family car and I want to pay about £5k and get something with a few extras. So far I have looked...
I have a 1995 2 Ltr 626, it is one of the best cars i have had. There has been no major problems as yet, and the car is a dream to drive. The only faults i...
cheers for the reply, I find it hard to understand why certain cars are so highly regarded and others overlooked. IS there anywhere I can find out more about...
hi, im a teen not a grandma, thats just what my friends call me. anyway i just wanted to know if someone could tell me where i could get a bodykit for my 96...
Hi, and welcome to the club. In my opinion, and I've had quite a few 626's... The best models to go for are the older 92 - 97 range.. known as the GE.. these...
hi and welcome to the club. There isn't much available in the UK.. most of the kits will come from the States.. Erebuni being the widest available.. Here are...
I have just bought a 1995 n reg mazda 626 glx 2,ltr and up to now am very happy with the purchace it was cheap but had a few faults the main problem up to now...
I have just bought a 1992 Mazda 626 16 valve 2.0i ltr. I was what the '92 626 alloys were like, and how much should I expect to pay for a full set??...
There should be an A/C relay in the fusebox. The condensor fan relays, are on a small bracket, at the left hand side of the engine. (looking from the front)...
There were various types of wheel fitted to the 2.0 Ltr 626.. 4 types as optional extras, which were £800 for a set of 4 with tyres. The standard size was 6J...
I am a new member to this site as well as a new 1'st time owner of a 92 mazda 626. I would ike to see some photos of other 91-92 / 626's. It does not mater if...
Hi and welcome to the club. There are some photo's in the photo section.. the model range changed in 92, but there are pictures of models from 87 - 92 and 92 -...
Hi John, After replacement of head gasket, when the engine runs hot, sometimes it will misfiring & the rpm drop (happened but not often). I know it is...
Since I'm in the US I looked under the dash on the drivers side and found a module that looked right. I thought I had found the alarm module but it turned out...
The usual cause is an air leak, somewhere in the pipework. Other causes can be oil in the plug wells (from a faulty or overtightened rocker cover gasket) or...
Nearly all of the electrics are made by Mitsubishi... The box you found could be the ABS control box. This keyless entry module you have, is it made by mazda,...
