hi john, just happened this afternoon, when i speed up to around 3,000rpm, the engine suddenly drop 200-300rpm & back to normal. its happened a few times on 3...
Hi Xavier, First you need to recheck for stored codes.. just in case you do have a problem, the codes will come back. as for the ABS ones, it is not a case of...
hi john, thanks for your input. i'm now managed to cleared off all codes. i will drive the car for a week time & recheck code again. will let you know later &...
after having misfiring at particular engine temperature (running) I've checked and replaced all the spark plugs, purchased from dealer. Now the misfiring...
Have you replaced the plug leads... the design of them (deep plug wells) means they don't last much longer than 80,000 KM's This is a common problem with most...
hi john, after a week driving, the auto transmission codes return again, the same 4 codes. how should i start to repair these faults? 1) ten to gnd (engine) ~...
What year and model is your 626? regards Simon ... _________________________________________________________________ Sign-up for a FREE BT Broadband connection...
Hi Xavier, As I said before, I think all the transmission problems are electrical connection related.. in other words, poor joints. 12.. wire between TPS on...
Things to check.. The plug gap should be 1.0 - 1.1 mm The Idle speed should be 700 +/- 50rpm Take out the air filter, and replace the cover.. start the engine ...
Filter was replaced with original one. what I did yesterday is to buy another set of plugs (NGK, made for Nissan, with same specs as rqd for 626). Now engine...
i had my alternator replaced with a 90A unit some time ago. i noticed a problem recently (after the alternator belt was replaced). namely, under heavy...
Std plugs are NGK or Nippon denso.. both are equally good. It is always possible that plugs can be faulty, even when new. Glad it's running fine now. John...
This sounds farly normal to me... it is not recommended to operate all four windows at the same time, because it can overload the wiring.. My only suggestions...
1994 626 LX V6 manual transmision I need to replace the thermostat, where is it???? I need replace the turn signal bulb in the right headlight, is it necessary...
Thermostat is at the front of the engine. (large pipe going from it to radiator) remove bolts from thermostat housing to remove. when putting new one in.. make...
Happy New Year !!! I have got a Mazda 626 1.8 LXI, Hatchback model 1992-1997 shape. I would like to upgrade to a performance air filter. I am think to get the...
Happy New Year !!! I have got a Mazda 626 1.8 LXI, Hatchback model 1992-1997 shape. I would like to upgrade to a performance air filter. I am think to get the...
Happy New Year I have got a Mazda 626 1.8 LXI 1992-1997 shape I am thinking to upgrade to a performance Air Filter Does anyone know whether the Universal...
You remove the existing airbox, (with filter) and fit a cone shaped filter over the end of the VAF and fasten with the jubilee clip supplied.. a better way is...
Thanks for your reply Do you know what size (Diameter) is the Standard Mazda Manfcaturer VAF on a Mazda 626 (1.8) LXI 1992-1997 model Do you think the...
Hmm, my 1995 already had CAI from the factory, collecting air from the front edge of the hood, in front of the radiator. It didn't have a big ugly cone filter...
... hello again John, I pulled the codes as per the document, and got an 03 (crankshaft position sensor). I assume it was an 03 because the LED only flashed 3 ...
The crank sensor is in the distributor... Mazda will normally only sell a complete distributor, and not the part to repair it.. Ford will sell the ignitor...
I am currently in Australia, trying to fix my 1998 626 2.0L that has a problem with the power windows. The problem relates to a small 5cm nylon/plastic cog...
Hi Tadpole, Looking in the manuals, it doesn't show the cog as a seperate part. I think you are going to struggle to find a brand new replacement.. My advice...
... hi, where could i get a copy of the wiring diagram for the distributor? there are 2 connectors which go to the distributor, a large one and a small one....
As I said before, you dont need a full distributor, just the ignitor module, this has the sensors built into it. As for the wiring diagram... no problem, I...
... Hi John, thank you again. you are truly an invaluable resource person on this group. :) regarding the distributor, yup, i heard you. the trouble is that in...
