You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
hi, me again with the intermittent misfire. i got myself the Haynes manual and it says that code 03 is CAMSHAFT position sensor. i reset the ECU twice to clear...
Hi Orlando, 03 code is the distributor G signal.. According to the manual, if there is a fault with the G signal sensor, the engine will still run, but it will...
... hello, what does "cancel sequential injection" do? as an aside, I'm still getting 7km/L city and 10km/L highway. this might seem kind of low but it's the...
... No idea, just what it said in the manual. ... to ... The centre console removes easy.. there is a small plastic clip at the rear of the tray, just in...
I`ve just put a brand new o/s headlamp on ebay, heres the link.. http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=2459196873 As you probably know they are...
Hi John, After I drove the car for nearly 4-5 hours, when slowing down, the rpm suddenly drop to zero & engine cut off. The "HOLD" lights on for about 1 second...
Most of this points to poor connections between the ECU and ATX control box (under centre console) 12 is the throttle position sensor, which again is connected...
I have done so, nothing has changed, same codes again. :-( ECU connections are good & clean, if these were the wiring problem than it will be at the gearbox...
Hello Everyone I have recently purchased a K&N 3.5" Universal Air Filter (Cone Style). And I have removed the existing manufacturer Air box and replace it with...
replied via email... The no1 pipe, is for the emissions and just vents a small amount of vapour back into the engine, this can be plugged, or left open.. The...
you are right, i have sent in to mazda workshop for checkup, what there did are check the wiring from the a/t controller (behind ecu) to ecu & also to gear...
help! there's a leak in my (front) window washer tank. the haynes manual has no information on how to get the tank out of the car, and how to fix the leak. ...
as far as I know, the tank will come out from underneath the car.. Start with removing the plastic wheel arch covers, you should get a better view of things.. ...
i have excessive play in the clutch pedal. i took a look at it for adjustment purposes and it seems there is very little resistance from the pushrod until the...
It is most likely The pedal needs adjusting, or there is air in the system, or a fluid leak.... I have posted a page on pedal adjustment in the tech section......
... I checked the pedal adjustment (since the procedure is documented in Haynes) but the adjustment screws are at maximum already. Regarding leaks, if there is...
the engine will die-off after a few hours driving (2 hours or more). no codes has stored. when it start die-off, it will die-off again every 5 - 10 minutes...
It does sound like the ignitor module in the distributor... best advice is to buy the ignitor module from a Ford dealer, as Mazda will only sell a complete...
Very much a DIY project.. Basically, remove the distributor cap, a few more screws inside and the module and coil will come out.. just as easy to replace. for...
Hi, and welcome to the club. I would say anything is possible, if you have enough money.. although in this case, it may be cheaper than you think. The Protege...
626 executive 1989 (F) Drivers stored is stuck shut. Everything works OK, other doors, central locking etc, the knob goes up and down - the door just will not...
I have 92 mazda 626 GE and I noticed some coolant leak. After that I saw that coolant (some green liquid) is dripping from a hole under the car located near...
To remove the door card, you need the door open, as one of the screws is on the side.. it looks like a faulty lock, or the rods have come off.. You may have to...
Strange is the correct word... there are no coolant pipes inside the car, other than the ones that go to the heater matrix under the dash.. If there was any...
I have a 1988 626 coupe 2.0l 16v that has recently started to smoke quite heavily at start up. Its also using water at the moment but with no apparent leaks....
Hi Zack, and welcome to the club.. This depends on the colour of the smoke on startup.. Blue, and it's oil related, probably the valve stem seals as you say. ...
