mazda626uk : Messages : 877-909 of 2676

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

877	how difficult to replace it? diy possible? xavier goh ... From: John To: mazda626uk@... Sent: Tuesday, 30 March, 2004 7:35 PM Subject:...	Xavier Goh SH xavier_iet	Apr 5, 2004 7:46 am
879	Very much a DIY project.. Basically, remove the distributor cap, a few more screws inside and the module and coil will come out.. just as easy to replace. for...	John compyshop	Apr 12, 2004 7:19 am
880	thanks. i will try to get one from ford. it should be the same cause mine one also v6 engine (kf model). xavier goh ... From: John To:...	Xavier Goh SH xavier_iet	Apr 12, 2004 8:26 am
881	I would like to change my Protege rear brakes from drums to disc. Is it possible? if so were I can find info. Thanks!...	byako1950	Apr 24, 2004 1:06 am
882	Hi, and welcome to the club. I would say anything is possible, if you have enough money.. although in this case, it may be cheaper than you think. The Protege...	John compyshop	Apr 24, 2004 10:06 am
883	626 executive 1989 (F) Drivers stored is stuck shut. Everything works OK, other doors, central locking etc, the knob goes up and down - the door just will not...	pqx4a63	Apr 26, 2004 9:34 am
885	I have 92 mazda 626 GE and I noticed some coolant leak. After that I saw that coolant (some green liquid) is dripping from a hole under the car located near...	p0luxus	Apr 28, 2004 2:33 pm
886	To remove the door card, you need the door open, as one of the screws is on the side.. it looks like a faulty lock, or the rods have come off.. You may have to...	John compyshop	Apr 28, 2004 8:27 pm
887	Strange is the correct word... there are no coolant pipes inside the car, other than the ones that go to the heater matrix under the dash.. If there was any...	John compyshop	Apr 28, 2004 8:36 pm
888	I have a 1988 626 coupe 2.0l 16v that has recently started to smoke quite heavily at start up. Its also using water at the moment but with no apparent leaks....	zack_77_uk	May 10, 2004 1:43 pm
889	Hi Zack, and welcome to the club.. This depends on the colour of the smoke on startup.. Blue, and it's oil related, probably the valve stem seals as you say. ...	John compyshop	May 10, 2004 5:17 pm
890	John Many thanks for your help and advice..! I'll let you know the outcome. regards Zack ... and welcome to the club.. ... ...	ZACK Warnes zack_77_uk	May 10, 2004 9:16 pm
891	hello! Einstein! I have a Mazda MX6 '93 LS/V6 stick/manual shift. and also think I have a lotsa problems. When in first gear, it won't move that much, its like...	hkoratala	May 13, 2004 6:51 pm
892	Hi hkoratala, and welcome to the club.. there should be no hesitation or "holding back" in first gear. It could be related to the codes you have pulled. ...	John compyshop	May 13, 2004 9:47 pm
893	Anyone know where i can get lowerings springs for mye Mazda 4WS??...	nomiex	May 17, 2004 1:31 pm
894	Hi nomiex.. Eibach make the best springs, and they are available for the 88 - 92 models.. part no 5511.140 they should fit the 4WS as well.. although the...	John compyshop	May 17, 2004 7:43 pm
895	I don't know where to go online to get exploded views that are detailed and accurate here in the US for my 96' Ford Probe GT 24 valve 2.5 L (Mazda 626 engine...	Sondi sondistewart	May 24, 2004 4:40 am
896	Hi Sondi, and welcome to the club... Yes, I have everything you need.. (full genuine Mazda workshop manuals in fact) In the photo section there is a technical...	John compyshop	May 24, 2004 11:49 am
897	Hi If possible can anyone provide me with a diagram for installing a new timing belt on the 2.0l 16v FE3N engine.. Many thanks ZACK...	zack_77_uk	May 25, 2004 8:50 am
898	Hi Zack, and welcome to the club.. I have emailed you the details. John...	John compyshop	May 25, 2004 12:17 pm
899	Oh my gosh, I am so greatful for your response and the help you are willingly offering. I really don't think you have any idea how huge of a help you have...	Sondi sondistewart	May 27, 2004 6:24 pm
900	I have sent the pipe routing diagram via email.. Most of the electrical connections will only fit in their respective sockets.. and the length of cable will...	John compyshop	May 28, 2004 11:55 am
902	Hello All Just registered as I have come into possession of a white GT coupe. The question is what do I do with it? I see 3 possibilities: 1) Scrap it 2) Sell...	Vulpine9 jon_w_fox	May 28, 2004 11:40 pm
903	Hi Jon, and welcome to the club.. I looked at one of these once, and very nearly bought it.. known as the 1st generation MX-6 in other parts of the world.. ...	John compyshop	May 29, 2004 12:13 am
904	Thanks John I do like its looks and the ABS/adjustable suspension/cruise control are amazing especially for an e reg! I am normally a Manta fan and they had no...	jon_w_fox	May 29, 2004 12:26 pm
905	Hi Jon.. Manta eh? I used to have an old T reg Kadette coupe 1200s... then decided to drop the Manta running gear in it... god was that one terrifying car... ...	John compyshop	May 29, 2004 5:48 pm
906	I am getting some leather seats shortly for my car.. If anyone is interested in my old ones out of my 626GT which are in excellent condition, just ask.....	John compyshop	Jun 4, 2004 5:32 pm
907	Is it 140-150 or is that the turbo version? thanks Jon...	jon_w_fox	Jun 6, 2004 7:20 pm
908	For a 1988 626 GT coupe 2L 16v non turbo: 1) Exhaust downpipe 2) OS outer sill 3) radiator Going to visit scrappies over the summer as i also need some other ...	jon_w_fox	Jun 6, 2004 7:26 pm
909	Dear All How do I obtain the full size images in the albums? Can only access the screen image versions which are unclear. Am I missing something obvious? ...	jon_w_fox	Jun 6, 2004 8:04 pm

Yahoo! Groups Tips

Did you know...

Messages