John..I am having a problem again with the Front Nearside Passenger door window Motor.I have had the door trim off[your suggestion] and given the motor a...
i bought the car second hand and was told that the valve stem seals were gone. we paid the chap £90 for the parts and he said that he would do the job for us...
Hi Michael. Only thing I can think of is to strip the complete mechanism, give it a really good clean, and regrease it.. if that doesn't cure it, then it will...
Hi Dave and welcome to the club.. Well, looks like you are in luck mate.. I have the original workshop manuals.. and can email you the relevent pages to do the...
John..Thanks for the info.Just a thought,the Haynes Manual I have is 929 which covers years 1983 to 1987 and doesnt give a very good view of the window power...
There is not really enough detail on the assembly, just that it is one complete unit.. It says to have the window about 3" from the bottom when removing it. ...
Hello all, just recently acquired a ride, and I want to modify, both in and out. I recently bought a few things to mod it which basically didnt have much...
Modding a car is perfectly legal so long as you follow the normal regulations.. in short, if it will pass an MOT test, then it is legal.. Some things that are...
sorry to be a pain but after 2 days of trying i can't get this dam car set up (626 "N"95) it is so close it sounds like a car on a cold morning despertly...
yes.. 1342... and no1 is at the timing belt end :-) And double check the timing belt marks just to be sure.. and check the distributor isn't 180 degrees out...
the distributor was 180 out at one stage and the engine just turned over
not even trying to fire corrected that and now she's trying to fire. i've
had real...
Dave, you need to turn the engine over by hand, and check all the marks line up as stated in the manual.. one notch out anywhere, and you'll need to adjust it....
hey, thanks for the reply...now, is anyone experienced with fitting spoilers at all? ...if you can check out my page (www.eatdustsuckah.mypiece.com) you will...
The std built in spoiler is hollow GRP... it's more plastic than fibreglass.. You would have to bolt through all of it, but then have difficulty in tightening...
Thank you sorry about the last e-mail i was a bit miffed off as you could
with no dout tell!!! if all belts and crank shaft are removed timing belt
replaced...
If you mean without the alternator belts etc, yes, it's safe for a short while... It should just be a case of lining it up correctly.. if it still won't start,...
thanks for a speedy reply havent been out today little girls 5th birthday we
bought her a little electric scooter wich goes a top speed of 3.3mph (wow)
and she...
John. Thanks very much for your time to inform me. I will look into what options I can do. did you say I can unbolt the hatch from the inside? what about using...
Yes, there are 5 nuts on both sides going down the inside of the hatch.. undo these, and the spoiler should lift off. you will have to pull the inside trim off...
K, thanks, will get back to you as soon as I figure this out...(will post some pix after, and see how it turns out) ;) ...hav u got pix of your ride? while...
Hi, all Mazda lovers! I'm new to Mazda. Just switched over from Renault and bought 2nd hand Mazda 626 '98. Please suggest where to find information for a ...
Hi Karosas, and welcome to the club.. :-) Your plugs should be NGK ZFR5F-11 Oil is SG grade, 10W-30 (semi synthetic or fully synthetic)Around 3.5 litres. Only...
Hi John, thanks for your reply and advices + info. Still have open questions about intervals to change liquids and belts, mainly the timing belt. Normaly as I...
Hi Karosas, The service intervals are probably 12,000 miles (20,000 Kms)or 12 months. timing belt possibly 60,000 miles (96,000 kms)... doing the tensioner at...
Hi Karosas I have a '99 626 and recently changed the timing belt. See all the posts around september for all my questions and the responses from the group. On...
Hi John, Just on today, I found the cylinder 1 was miss firing, I took out the plug & found that there is some oil mark on the tip of the plug. I am suspect...
