In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
In using rifles to the outmost accuracy,and full potential,it is nessesary to
clean the barrel regularly.A hunter shooting a rifle few shots in a single
day,should clean the the barrel at end of day.A match shooter shooting in
competition cleans barrels after 8-15 shots.
It is a good rule to clean barrel when 20-30 shots are through as a maximum
shots fired.
This depends on size of cartridge case,and bore diameter.The larger the
cartridge case versus smaller bore diameter,then the more frequency is needed in
cleaning.
Cleaning Method 1.
After shooting X numbers of shots,the target, varmint or big game shooters
should use following method.
Wet 2patches with cleaning solvent (I use Shooters Choice),push from rear,up
front through barrel.This takes all loose fowling out.
Next it is best to brush the barrel with copper brush,soaked in cleaning
solvent,about 10 passes,through barrel.Add solvent to brush after few passes,at
muzzle end when brush is out of barrel.
After these passes 10 maeby 20 depending on quantity of shots fired and
condition of barrel,2 dry patches are pushed through barrel from rear.
Now the barrel should be almost clean ! To clean better it is advisable to soak
a plasic brush or fiber brush with solvent and wet the bore of barrel ! Let it
stand overnight,and check color of solvent next day.
It may come out light green or strong green,depending og fowling in barrel.If it
comes out strong green,brush some more with copper brush,and repeat wetting bore
with solvent,and let it stand overnight.
Wetting barrels is only advisable with safe solvents,read the bottle
instructions.Some stronger Ammonia blended solvents can damage barrels if left
too long in barrel.
It is advisable to leave barrels wet until next shooting starts.
URGENT ! DRY BARREL OUT BEFORE SHOOTING .
Cleaning method 2.
Some Rifles can have rough bores,and fowl badly.
For cleaning them it may be nessesary to use stronger Solvents Ammonia
blended.Use the Ammonia blended solvents carefully and only for soaking wet for
15-20 mins.Don´t brush them in with copper brush,this will ruin brush,plasic or
fiber brush.Even abrasives may be used to get out severe fowling,but work
carefully with them ! Best is to use patch rolled around a cleaning jag and push
through barrel in short strokes,gradually towards the muzzle end.
After using Ammonia blended solvents,and or abrasives,it is advisable to use
milder solvents to clean barrel and do the color check overnight !
When cleaning process is done it is good workmanship to drye out chamber of
gun,clean locking lug aeria,inside of action and put small dips of grease on
locking lugs.
Good Shooting !
The following file was arranged to be sent to the precisiongroup
group automatically.
File : Bench Rest Intro..mpg
Description : Bench rest Introduction
Size : 4272 KB
However, due to the large size of the file, it is not sent
through email. Instead, you can access the file at this URL
http://uk.groups.yahoo.com/group/precisiongroup/files/Bench%20Rest%20Intro..mpg
Hello Members !
Just launched my B.R.S.Custom Rifles VIDEO STORE !
http://www.lulu.com/shooting
Hope you Enjoy.
B.R.S. Custom Rifles.
Birgir Runar Saemundsson
Hello Group Members !
New Links to Google Video !
Interesting info for rifleshooters !
Bench Rest Video Introduction !
http://video.google.com/videosearch?q=%
22Bench+Rest+Shooting+Introduction"+playable:true
=====================================================================
==================
Bench Rest Video Shooting in USA 1989.
http://video.google.com/videosearch?q=%
22Bench+Rest+Shooting+in+USA+1989"+playable:true
=====================================================================
=========
RuV TV show Sports
http://video.google.com/videoplay?docid=-7890217484809668602
NEW websites in the building now
www.rifflar.com
www.better-rifles.com
www.best-rifles.com
http://brs-rifles.blogspot.com/
Take a look !!!!!!!!!!!
Sincerely
Birgir Saemundsson
--- In precisiongroup@..., "sirperfect01"
<sirperfect01@y...> wrote:
> hi i live in the north east is there any clubs please,joe
Hello Joe ! Where in north east do you live ?
I live in Iceland !
Please send line .
Birgir Saemundsson
TEL.+354 8480966
Dear members !
The activity of group is very little !
We need to do something to activate group.
Please communicate your questions and your consearns ,and maybe
someone will give some light into life !
I know I have many answears but not all , but I will do my best to be
of service as a dedicated Rifle match shooter , so please shoot !!!!!
As your servant
Birgir Saemundsson
Dear Shooters .
In progress is a schedule to have Hunter Class Shooting competitions
this coming summer,in Iceland .
Most likely it will be held at Egilsstaðir .
Interested shooters please contact me ,or post here .
Icelandic Hunter Class Federation
Birgir Sæmundsson
Happy new year Precision group Members !
We are still few,but have grown 300 % so far in less than half year !
Wish you a happy new year and thanks for past year.
Soon there will be added more Video links to the Links page,some
video shots from a sporting program on Icelandic TV RUV.
Which will show Target shooting at 100 M.Very interesting to watch !
All the best to members.
Birgir Saemundsson
Merry Christmas to Precision Group Members !
Happy holidays and have happy Christmas.
We are still few but,we are a group !
More tech articles will be added soon along with video shots.
We will grow in 2005.
Have a happy New Year
Birgir Saemundsson
Hello grouppies !
Brand new photos now posted on Photolink.
Competition Rifles and hunting rifles among other things.
Soon to come Video shots of competition shooting etc.
Moderator .
Hello,
The moderator of the presisiongroup group has changed the
group's name. This means that both the group's email address and the
group home page location have changed.
The group email address:
precisiongroup@...
The group home page location:
http://uk.groups.yahoo.com/group/precisiongroup
If you have links which point to this group or an address book entry
for the group, you should update them, as the old addresses will no
longer work.
Regards,
Yahoo! Groups Customer Care
The objective of this group is to get knowledge out to Shooters and
competitors in Rifle shooting.Main interest regarding presision
match shooting,Varmint Shooting,and long range shooting 1000yds and
longer.The issues here are cleaning of barrels,cartridge
reloading,riflescopes,actions,barrels,shooting teshniques,and all
related knowledge to Presision Rifle shooting.
Another issue of this group is Riflesmithing,Competition
rifles,varmint rifles,and Long range rifles,Action building.
Comprehensive knowledge base to search through,covering over 30
years of experience in Rifle Smithing and Competition Shooting !
Good shooting !
Group Owner
Send Email
Offline 
