Has anyone had any problems with the SPROG changing something in a decoder to a point that it wont functtion properly. Now before everyone jumps in and says...
The new test release of JMRI contains the first version of "DecoderPro 3". This is focused on the management of loco decoders, and as such, relevant to Sprog...
How does an owner of a Sprog access a decoder that is NOT listed. With new decoders coming on to the market could this not be a problem for users? Regards....
Having bought a Sprog 11 being impressed with the benefits, I soon ran in to problems. Following the manual to get it all started and downloaded the JMRI and...
Hi Trying to solve a problem. I am trying use a Team Digital SMD82 to control 4 points on my layout using SPROG for the DCC signal but have hit some problems. ...
Andrew Do you have a usb driver for Android to work with sprog 2 useing usb port on a phone ? If yes Do you know of a app to run locos, If not When ? Regards...
Hi Group, My first posting :-) But bit of a dire one unfortunately. Ive only had my SPROG II (Firmware 2.7) for about 5 months. Ive either blown my SPROG or...
While looking over the release notes for JMRI 2.12 i notice that Andrew (Crosland) has "Added support for SPROG 3." Is that a new version of the Sprog II or...
Hi When updating software on Sprog - Is older version deleted first ? Is it done with Pic installed ? (no need to remove for re programming?) Can a 9 pin...
Hi my emu has a loksound micro v3.5 olivias sound 4cep on. sometime ago i lost the start up cv through leaving my emu on the programing track whilst programing...
First apologies if this has been covered before – I did a search but couldn't find anything similar. Having used a JMRI throttle on my PC via a Sprog II and...
Thanks Ian That makes sense. I got 1, 2, 4 and 5 in the right order but omitted 3 (probably because it's not switched - but I'll make sure it's unplugged from ...
HI I have only some loco decoders for use on other layouts. All I want to do is to be able to read the cv's etc and change as required. I do not require to...
Hi, My SPROG II was working flawlessly until yesterday. I was using it to change some parameters on friend's locomotives (QSI decoders) during an exhibition...
Hello Members, I am totally new to SPROG and to this group, but I was told by some enthusiasts with a lot more experience than me, that I should explore SPROG....
Hi all, I've recently read about Roco boosters to be used for the SPROGII. Which other boosters are suitable, and relatively inexpensive to use? What I'm...
I am looking to buy a 5 amp booster for my sprog and I have narrowed the list down to 4. MRC 1521 $115 DIGITRAX DB150 $140 NCE DBA3 $93 LENZ LV102 $154 Please...
We seem to have a lot of "this didn't work" and "I need some help with . . ." messages on this group, and that's not a big surprise of course given that's the...
I uploaded this video for sprog tech support. http://www.youtube.com/watch?v=NlIHnRUqZew This is a brand new sprog II and the power supply that it came with. I...
Hi, I have an Atlas S2 that I fitted with an MRC #0001663 decoder. The instalation went well (done some time ago). The volumn is too high. I have downloaded...
Hi I have a Macbook and have successfully managed to get a few trains running used PanelPro, does anybody know how to connect the SprogII to the Lenz LZV100 to...
Hi All, I am new to DCC. I have purchased a Sprog II and at present operating a loco fitted with a Digitrax DZ125PS decoder. The loco operates without any...
At least that's how I think of it, they describe it as 'stationary controllers where you add the voltage': http://auxboxdcc.com/ One thing that impressed me...
I got my SPROG to work through DecoderPro to read and write the QSI Revolution Ver 7. Here is the fix - Take two 22ohm 1/4 resistors and twist them together....
