That is my experience over several years of sprog use - does not matter on power up sequence (I frequently reset my Sprog by just disconnecting its power...
1557
Peter Broadhead
pjcxb
Feb 3, 2012 8:34 pm
Many thanks to Nigel, Kevin, Graham and Andrew for your replies to my posting. The problem was that I had not noticed the need to turn on the power to the...
1558
ncliffe2001
Feb 4, 2012 9:23 am
Do not upgrade Sprog firmware without satisfying two criteria: a - you have a fault b - you have checked with Andrew Crosland, the maker, that a change will be...
1559
andrew_croslanduk
andrew_crosl...
Feb 4, 2012 10:13 am
Version 2.6 is fine. If you are in the habit of switching between sprog mode and sprog command station mode then there is an issue to be aware of. Even in...
1560
Michael Watnoski
frestate
Feb 4, 2012 2:34 pm
Hi Graham, I am glad you were able to get it to meet your expectations. Apparently adding the diesel sounds and lighting features were a secondary ...
1561
graham_wass
Feb 4, 2012 2:48 pm
... On looking at all the forums it seems it is the Diesel side that is causing probs. For me the steam side is working fine and well pleased. Have odred a...
1562
Phil Holman
phili1955
Feb 4, 2012 3:19 pm
HI Andrew, Thank you for that bit of information! It answers the problem we had at the last exhibition. Phil Holman _____ From: sprog-dcc@......
1563
tarabuses
Feb 5, 2012 6:51 pm
I seem to have v1.4. It works fine but am I missing anything? Tony...
1564
pjrose0134
Feb 5, 2012 7:45 pm
Hi all Over the past few days i have installed a sprog and have many problems with it, Thanks to Andrew B it is now working. the other evening i was still...
1565
Mark
szczowicz
Feb 9, 2012 10:49 pm
Is there some reason why SPROG II on my system does not recognise either the Digitrax TL1 or TF4 function only decoders when trying to program them. However...
1566
Barry Draper
barry_draper
Feb 9, 2012 11:54 pm
Mark, You need to have a lamp or resistor connected between the blue wire and both function 1 and function 2 outputs for the Ack pulse that allows readback on...
1567
andrew_croslanduk
andrew_crosl...
Feb 10, 2012 12:51 pm
It's the current required for a LED that is the problem, way too low. Official spec is that you need at least 60 milliAmps. With the normal 12V power supply...
1568
pjrose0134
Feb 10, 2012 6:20 pm
I have sucsesfuly programed about 15 locos into my sprog roster and the majority of them run well in the control mode, However I have 2 that run well in...
1569
Kevin Dickerson
kw.dickerson
Feb 10, 2012 8:24 pm
Peter, One thing to do is either power reset the Sprog when going from one mode to the other, or before you leave programming mode, set the address on the...
1570
pjrose0134
Feb 10, 2012 8:58 pm
Thanks for your reply Kevin. I will try what you have surgested tomorrow Regards Peter...
1571
Mark
szczowicz
Feb 12, 2012 3:03 pm
Barry, Andrew, Thanks for the replies. Had me a little mystified! Mark...
1572
andrew_croslanduk
andrew_crosl...
Feb 16, 2012 7:50 pm
I am pleased to announce that we have finally released the SPROG 3 and SBOOST on the SPROG DCC website. SPROG 3 is a higher current version of SPROG II that...
1573
dccdummy
Feb 16, 2012 10:35 pm
Hi guys, I'm new to the group but not to Sprog, I've been using mine for the last six years and have found it very useful. My problem is 2 Lenz silver decoders...
1574
alain c
acarasso_fr
Feb 17, 2012 12:32 pm
Hi Paul It could be that the decoders are in trouble. I had the same problem with a LE1025. The solution is to send an email to Lenz support, They can suggest...
1575
Paul And Romy Dunn
dccdummy
Feb 17, 2012 2:56 pm
Alain, Thanks for the advise. I took the decoders to A&H the Lenz agents to reset and they fixed them. Unfortunately they reset the decoders to CV 3 so I had...
1576
K2K Koos
torikoos
Feb 26, 2012 9:50 pm
great news Andrew, I'll sure be ordering a few SBOOST items in due course. One question, with the higher current output, is this also available in programming...
1577
ncliffe2001
Feb 27, 2012 9:49 am
If its unchanged from the prototype Sprog3 (I have one), then there is a considerably larger "jump" in locos being programmed than with a Sprog2. That...
1578
andrew_croslanduk
andrew_crosl...
Feb 27, 2012 4:07 pm
More robust than the prototypes :-) The track voltage from a SPROG 3 is closer to the power supply voltage that a SPROG II. That will contribute to the loco...
1579
andrew_croslanduk
andrew_crosl...
Feb 27, 2012 4:10 pm
I don't know what a QSI Revolution is :-( Is a SPROG II not able to program it? It can handle other sound decoders (including QSI). Andrew...
1580
K2K Koos
torikoos
Feb 27, 2012 6:52 pm
Hi Andrew, The Revolution was a DCC decoder made by QSI until recently, it has now been superseded with a newer version called Titan (among others now stereo...
1581
andrew_croslanduk
andrew_crosl...
Feb 28, 2012 3:53 pm
We can ship (almost) antwhere :-) Andrew...
1582
Mark
szczowicz
Mar 14, 2012 1:36 pm
Koos, I was beginning to doubt my sanity when I could program one of a pair of identical Atlas diesels with QSI series 7 decoders perfectly using the SPROG II...
1583
Frolin Marek
frolinmarek
Mar 16, 2012 4:14 am
Evening, Seems the upgrade to JMRI Decoder Pro 2.14 maybe coninsided with a failure is using my Sprog II. Had this issue 2-3 years ago (see thread on 'no...
1584
Gerry Hopkins MMR
gerrymmr
Mar 16, 2012 4:56 am
Frolin I cannot give you a fix, but, my Sprog II works on my old computer running Windows XP with all updates, on my netbook running Windows 7/32 and on my...
1585
Frolin Marek
frolinmarek
Mar 16, 2012 5:14 am
Jerry, Yea the Sprog worked great until I upgrade to JMRI 2.14 version. Think the JAVA says 1.6, does that have to be updated to use 2.14 JMRI? Odd is, even...
