You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
Hi everyone, What a coincidence that is, I was just about to go one line to my Yahoo groups and lo and behold Sprog springs back into life. I have just...
Got a Sprog for Xmas from my lovely wife. Works quite well. Working on reading my locos and saving the files in DecoderPro (I use a PowerCab for my in-progress...
Well as a new member, I'm sure I'll get some posts going. I'm awaiting the arrival of a USB SPROG on the recommendation of Paul Martin as I can't change the...
well, tonight I instaled my USB SPROG, but the results I got didn't seem to agree with the set-up instructions. When I tried a known loco on the program track...
Andrew, Thanks for your interest. I'm going to hold fire on this for the moment for 2 reasons A) I've ordered a 12VAC-DC supply from DigiDave in Jersey - I was...
... writted: I was trying mine on the 1V o/p from a Bachmann controller - so I may be contributing to my woes. ... What I meant to write was :- I was trying...
OK, Andrew, I've done a re-install - According to the JMRI debugging section everything is OK. However I'm getting timeout errors all the time. I'm connected...
... 'scuse me for butting in. I have my sprog USb set to 9600 baud, hardware flow and iut seems to work OK. Try that David. Larry Costa ... debugging ... the ...
Andrew, CAN you give me any update on the QSI V7 read-write situation. I have been waiting for a solution from Bill Chown. Use my Sprog 2 all the time but...
Hi, Larry. No problems with you butting in - all the more help the better! Unfortunately I've tried that setting. Spent a bit more time on it after my last...
Hi, more butting in,,,,, I'm pretty sure I'm running pure default, my sprog auto lands on COM 9 as shown in device manager, (9600,8,none,1,none) the 2 "none"s...
Paul, My Sprog lands up by default on COM 4 and I have played around with the Port setting - Flow control - tried all 3 available settings. Your suggestion...
Hi Gang, When I use my SPROG II to program QSI decoders (in Broadway Limited switchers and a Proto2000 GP9), it sometimes has trouble reading CVs. DecoderPro...
I am considering buying a sprog11 - the question i have is whether it would enable me to programme the sound chip in the class 20 - things like the volume of...
Rick, Sorry for the delay. I've been away on a Jolly with the day job and a bit pre-occupied with non-railway things. I need to check in with Bill as to what...
David, Let us know how you get on with the bigger power supply when you return. As a general note when using JMRI, you do not need to worry about the port...
Jim, What kind of power supply are you using? You need a regulated DC supply and sound decoders in general can draw a lot of current during programming. There...
Hi (you don't give a name) It's more a question of whether DecoderPro will support the decoder. I believe it's an ESU Loksound decoder. Even if the specific...
... I'm using the 1.25 v supply that came with the SPROG II. ... Version 6. ... What would be an appropriate value and wattage? Obviously this isn't a big...
... Make that the 1.25 AMP supply. After working with the locomotives more tonight, I found that the GP9 presents more difficulty/frustration reading CVs than...
... does not read/write properly with the Sprog 2. I can program ok with my MRC PA system but would like to use the Sprog which has been very good with all the...
... Sounds familiar. The SPROG seems to succeed about 25 to 35% of the time with the P2K/QSI GP9, and sometimes it seems to make mistakes in the indexed CVs. ...
Andrew, The bigger PSU I ordered from you arrived today. I re-installed everything as per the instructions on the CD and still came up with continuous 'time...
