You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
Good Day all; I have the above set up, and just recently, like yesterday, tried for the first time to program a digitrax TF-4 function only decoder. What a...
Phil, some motors don't draw enough current for the ACK to be detected by SPROG/Decoder Pro. You may need to hold the wheels or some such to increase the...
Hi Ian/Paul, A function only decoder need to have a resistor (47k?) connected between one output of the sprog and the programming track, otherwise it can't...
Ian, Have you actually had to do this? You're the second person to have said this in two days but I've never had any reports of problems until now. Regards, ...
Phil, There's a similar problem reported on the Digitrax list, message 104253, where someone was trying to program with an NCE system. The advice was to fit a...
Hi Andrew and other responders; I tried all sorts of resistor combinations, but never across the function leads,,,, wish I would have thought of that, sounds...
Hi Andrew, Yes, with certain locomotives I've always had to take steps like holding the wheels, or increasing the weight (same effect) in order to get the ...
Hi Andrew and gang I have a SPROG and use JMRI to program my locos. Now, here is the problem. I want to change the sound profiles on a my Digitrax Sound...
Hi Group I have just part built my SPROG kit. upto the USB testing section. unfortunately I struggling. two separate issues I think ?? 1) My computer does not...
Ian, Unfortunately the answer is no, at least not at the moment. I am not aware of Digitrax making the sound download algorithm public but I will make some...
Andy, ... They are probably related. In case anyone isn't aware, the kit version is only available, to members, from MERG and is a slightly older (but fully...
Thanks Andrew Have double checked, but will triple check !!!, will also download AN232-02 from FTDI and follow advice,I have access to a scope, but ...
... That shouldn't be a problem. Andrew ... section. ... slightly ... attached, ... but ... responds ... change ... Double ... connector. ... assumes...
... Hi Andrew, Yes, I have used my SPROG to programme a Challenger, a Big Boy and some F unit diesels (all Athearn Genesis fitted with MRC sound decoders) and ...
Hi Andrew Got it working, yippee. Output of 5v reg quite low 4.2v I turned up VR1 full up. Output of variable voltage reg is now 12.7v Some voltage drop...
Hi Andrew Got it worki.…. `O' dear …. !!!!..... Tried to update Firmware to v3.9, unfortunately I did not see your warning about using DecoderPro on your...
Andy, Oh dear. It's actually an issue with the SPROG rather than DecoderPro as such. If you look at the very last line of the hex file and try typing that in...
Raul/Andrew.....that worked like a charm!!! now I can hear all the sounds on the Sounder. Is their a DecoderPro function panel available with more functions? ...
Andrew et al in the SPROG group (posted to JMRI, as well since some SPROG users may not be reading the Sprog group). the Broadway Limited Sound decoder is in...
James, Sorry for the delay in replying. I just posted this in response to ... SprogII....< ... (byte) Mode. ... into ... Apologies for not jumping in sooner....
Andrew???? ... Subject: Re: [BLI-PCM] Re: DC Master on sale at ModelTrainStuff for $24.99 to program Blue Line CVs Date: Fri, 16 Nov 2007 09:06:26 -0800 ...
I can write and read to Soundtraxx decoders with the SPROG without problem. I have a decoder I am using for sound only, but don't know if it is Sound only or...
It really depends how you interpret the NMRA RPs. Continued below. ... decoder ... Addressing ... Programmer, or ... That's quite clear. ... he is ... command ...
I fail to see why a sound decoder can work in direct byte mode and not in direct bit mode or paged mode. The speaker load excuse sounds like a smokescreen to...
