Chris, In addition to the Single CV programmer, you can access CV 64 through the Comprhensive Programmer (normal) view. There are actually 4 TCS M1 definition...
575
Chris Marrable
borg2657
Jul 3, 2008 7:16 pm
Hi Bill A big thank you I was using the wrong decoder file! When I did "Read type from decoder" it choose Train Control Systems / TCS Mx series decoders / M1 ...
576
fellow_puzzler
Jul 6, 2008 5:07 pm
For your interest, there is a new group.. http://groups.yahoo.com/group/Viessmann-Halt/ The Viessmann Commander, is the Ultimate in controllers.. also there's ...
577
andrew_croslanduk
andrew_crosl...
Jul 9, 2008 6:22 pm
JMRI 2.1.7 is now released. Although it is a test version, it does have some potentially useful features for SPROG users. The SPROG "Get SPROG Firmware...
578
andrew_croslanduk
andrew_crosl...
Jul 9, 2008 6:27 pm
Please use the new version utility in JMRI 2.1.7 (see previous post). If you have v2.4, then please read on. An update is now available to fix issues when...
579
andy_sollis
Jul 12, 2008 10:03 pm
Hi, I've used and fitted these before myself, and had no problems. Just been given one purchased this week to fit in a Heljan 47 (Loksound v3.5) for a friend...
580
andy_sollis
Jul 17, 2008 4:41 pm
Hi all, Done some more checking with this, tested fine on layout with Dynamis controller, but return to Sprog & decoder Pro, all is not well. The only...
581
Ian Birchenough
hida_yoshio
Jul 20, 2008 11:13 am
Guys, having some problems with my programming track. I use a SPROGII (I believe V2) hooked to my PC running JMRI version 2.1.7 I fitted a ESU locsound to an...
582
Bob Willie
caravanbob
Aug 26, 2008 2:26 am
Have a question, I have mounted my sprog in a home brew "all in one" holder that contains my dcc system, my sprog, and a few power supplies, as well as...
583
Dave
davelocke96
Aug 26, 2008 7:08 am
... one" ... supplies, ... switch ... sprog ... affect on ... at a ... for ... on a ... Hi bob the only problem i have had leaving the sprog powered up was ...
584
John Bicknell
johncb50
Aug 26, 2008 11:39 am
Bob, I have inadvertently left my SPROG unit 'powered up' for many hours, sometimes overnight, without any obvious problems (so far!). I also have a switch...
585
pdsteam@...
pdsteam
Aug 26, 2008 4:18 pm
I usually leave mine power up, sometimes for days at a time, and have not had any problems. I also have my railroad equipment electronics running thru a UPS to...
586
bob
caravanbob
Aug 26, 2008 7:49 pm
Thanks everyone!! I fell better now and can finish my project without worry!! ... From: <pdsteam@...> To: <sprog-dcc@...> Sent: Tuesday,...
587
fellow_puzzler
Aug 27, 2008 9:50 am
Please can someone give me some guidance on how to read the CV's using the Sprog on the Lenz LS 150 accessory decoder, I have tried to do this with out much...
588
andrew_croslanduk
andrew_crosl...
Aug 27, 2008 2:42 pm
I'm not sure if the LS150 can be programmed on a programming track. I think it needs to be "programmed" by sending accesory commands to it whilst connected to...
589
Clark Thorp
llyffant2000
Sep 3, 2008 9:34 pm
I am finally recovering from a lightening strike that took out all my computers. So now I have a new PC to connect to the layout and programming track. I...
590
andrew_croslanduk
andrew_crosl...
Sep 4, 2008 11:47 am
Clark, The Loco Buffer uses an FTDI chip similar to SPROG but you need to install the drivers for both in order to get the correct setup. i don't anticipate...
591
Dave Falkenburg
falkenrr
Sep 4, 2008 3:53 pm
... Both the Quantum Programmer and the NCE USB interface uses the SiLabs CP210x USB to serial chip. ...
592
Clark Thorp
llyffant2000
Sep 4, 2008 5:19 pm
Thanks, Andrew. Install Loco Buffer AND Sprog buffers and let Windoze figure out who drives what. I love it when (at least part of) a plan comes...
593
Brett Payne
firstupau
Sep 7, 2008 4:38 am
I bought my Sprog last month. I have installed it on a Dell Notebook that already has Java and DecoderPro installed and has (and still is) worked fine via its...
594
andrew_croslanduk
andrew_crosl...
Sep 7, 2008 8:45 am
Brett, Did the SPROG ever work or did this all happen from the first time you tried it? It sounds like the software setup is fine and the PC is communications ...
595
Brett Payne
firstupau
Sep 7, 2008 9:36 am
Hi Andrew, Answers below: ... Happened from the first time I tried it. ... Currently trying with an NCE D12SR which is working fine on the layout itself and...
596
andy_sollis
Sep 7, 2008 10:56 am
... Brett, I in no way mean this to sound sarcastic, so don't take it that way please, but is the track connection good and the decoder fitted well (I.e no bad...
597
andy_sollis
Sep 7, 2008 10:59 am
... system. ... system ... Just read your reply to Andrew on the web (I have messages downloaded as a group) - Sorry, I have been teaching you to suck eggs. ...
598
Brett Payne
firstupau
Sep 7, 2008 11:34 am
Hi Andy, Not offended at all. For everyones info I live in Australia and model US prototype. I have installed about 10 decoders myself in a combination of...
599
fjknight
Sep 7, 2008 1:10 pm
Brett, I model in Sn2 and the Forney type loco has a difficult time making continuous contact with the track because of its long frame. When I first put DCC in...
600
andrew_croslanduk
andrew_crosl...
Sep 7, 2008 3:06 pm
Brett, It sounds like you've done all the right things and the SPROG may be faulty. I've sent you a private mail about replacing it. Andrew...
601
Brett Payne
firstupau
Sep 7, 2008 11:31 pm
andrew_croslanduk wrote: Thanks Andrew....
602
andrew_croslanduk
andrew_crosl...
Sep 10, 2008 6:39 pm
Brett, Another suggestion based on experiences of another user. Do you have any other devices (even if not currently connected) that use "virtual COM ports"? ...
603
Brett Payne
firstupau
Sep 11, 2008 8:10 pm
Ah yes. I did try that. My Notebook only has USB and EasyDCC assigned COM5 via a USB to Serial adapter cable. This works fine. Sprog's install assigned COM6...
