You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
I am new to TinyCad and so far I have been impressed. I have a question regarding the grid spacing. I have used the normal grid spacing to set components on...
José, Thanks for the feedback - I will update the web-site when I have time. The compile is Visual Studio VC 2003. I have reports that 2005 doesn't quite...
I can't answer your other questions, but Adobe Acrobat Professional 6.x allows you to save a PDF file to a DXF file or many other graphic and CAD formats. You...
I tried Acrobat Professional 6 today but saving to DXF was not an option. I remember reading somewhere that GhostView may allow you to save the PDF to DXF but...
You might have a look at autotrace http://autotrace.sourceforge.net which can convert bitmapped images to dxf (amongst others) it's open source & GPL, works...
Thank for the suggestion Mark. I haven't checked Autotrace yet but I did some checking and Autotrace uses PStoEdit to generate the DXF output. This is also...
Hi there, I found the following bug. The schematic shows that the components pin is connected with a wire to other components(R5, R2, E12 and D3 and stays...
I have this problem too. Both on a win98SE laptop as a WinXP desktop machine. The version I use is 2.60.01 A solution to this prolem would be very much...
I have used Tinycad to produce netlist files, and imported them into FreePCB before with no problem, including from the file I am presently trying to use. I...
Is it possible to import TinyCAD netlist into Protel DXP so that one can do PCB layout in Protel DXP?...
rgoes01
rgoes01@...
May 22, 2006 7:47 am
459
I know a TinyCAD file can be converted to a pdf file, but I want to import an existing pdf layout into TinyCAD. Is this possible? It would sure make my life...
tls7bar
tls@...
May 26, 2006 4:10 pm
460
Hello, When I open the help file, some of the images do not appear. What might be the reason for that? I am using Ver. 2.60.00 with Win98SE Thanks for any...
When I use the syntax: R$(refnum) to place R1 on the netlist line where refnum I assume is the same attribure as reference, it generates R1R1 when reference...
Hello, I have built a symbol with 6 pins, 2 of which are classified as "not connected". This was done to keep the pin numbering correct and in synch with a dip...
The R1R1 designates that it is a resistor on sheet 1, as R2R1 would designate a resistor on sheet 2. I don't know how this affects running spice in another...
Hi, I am a newbe to this program, so bear with me. I would like to have a visible grid when I draw a schematic or edit a symbol. However, checking that option...
I used one of the bridge rectifier symbols from passive2 library in my schematic. The design check comes back with an error "not connected to anything". I...
Hello All, I wanted to go through the tinyCAD source code as an exercise in MFC programming and also to explore how I could use it as a frontend for an EDA...
Ashwin, I use visual stdio 2003 to compile TinyCAD. I haven't got a copy of 2005 so I can't help you directly, however, I suspect you can downgrade the error...
Hello, I am receiving similar errors. I am using Visual C++ 6. I downloaded the 2.60.00 code. I am getting a lot of errors. Any suggestions/help will be...
Hi Has anybody tried using Hierarchical symbols and created Parts lists which reflect the correct sub-symbol (normal symbol) quantities when using the...
epc_engineer
8kr33ajgr008ej001@...
Jul 5, 2006 8:06 am
478
... see my upload in files section. rename the "tinyCAD new.chm" into "tinyCAD.chm" and replace the original one. than you will also have a search index... ...
