You can set the sort order of messages? Just click on the link in the date column. Your preferences will be remembered, so you don't have to do it again when you return.
Ashwin, I use visual stdio 2003 to compile TinyCAD. I haven't got a copy of 2005 so I can't help you directly, however, I suspect you can downgrade the error...
476
aryajur
Jul 3, 2006 8:20 am
Hello, I am receiving similar errors. I am using Visual C++ 6. I downloaded the 2.60.00 code. I am getting a lot of errors. Any suggestions/help will be...
477
epc_engineer
8kr33ajgr008ej001@...
Jul 5, 2006 8:06 am
Hi Has anybody tried using Hierarchical symbols and created Parts lists which reflect the correct sub-symbol (normal symbol) quantities when using the...
478
mbrestrich
Jul 5, 2006 3:33 pm
... see my upload in files section. rename the "tinyCAD new.chm" into "tinyCAD.chm" and replace the original one. than you will also have a search index... ...
479
mbrestrich
Jul 5, 2006 4:10 pm
Hi Matt, the last two weeks I have done a German translation and overworked the english help also. I included an index on both and minimalized the htm code...
480
kb5cth
Jul 6, 2006 8:08 am
Matt and all, When I try to enter all of the SPICE model data for a typical 2N2222A tranistor, I get an error saying that I've entered too much data and should...
481
John Carter
johnecarter
Jul 10, 2006 7:56 am
I understand that there is limited support for using TC with Windows 98. My problem is that there are no Windows XP drivers for the plotter I have available...
482
marcuswaynus
Jul 15, 2006 4:53 am
I want to make you guys aware of this project. The mission statement starts out: The Open Symbol Project aims to create an open collection of schematic symbols...
483
Matt Pyne
mattpyne
Jul 16, 2006 6:19 pm
________________________________ From: tinycad@... [mailto:tinycad@...] On Behalf Of marcuswaynus Sent: 15 July 2006 05:48 To:...
484
evsource_com
Jul 16, 2006 6:21 pm
... John, I had the same problem with Win 98. I installed version 2.60.00, and it seems to work fine. I'm curious what was introduced in the latest version...
485
John Carter
johnecarter
Jul 16, 2006 6:22 pm
... Windows 98. ... I ... are ... the ... when ... get ... still ... on ... I got email from Ryan Bohm <ryan@...> who also has a Trek laptop with...
486
Don Lucas
mountain_reb...
Jul 17, 2006 5:25 am
Hi John – I’m old enough to have used the HP 7475A plotter on a VAX 11/750 back when it cost around $8000 to buy a new one. I find it very hard to believe...
487
Don Lucas
mountain_reb...
Jul 17, 2006 5:53 am
Hi John – I just realized that I had followed a different link than I thought regarding the shareware/$50 plotter driver. The detailed information that I ...
488
cjku3
research@...
Jul 17, 2006 8:30 am
I encounter the same probrem, and suggest the author to treat that as some kind of bug. C.J.Ku...
489
Paul Land
asktheprophet
Jul 18, 2006 3:00 pm
RE plotter on com port. I believe the command is in the form of; type filname.ext > com1 "type" being a command not instruction ... ...
490
Don Lucas
mountain_reb...
Jul 19, 2006 4:52 am
That should also work, but "copy filename.ext com1" should still work as well. You could also use "copy filename.ext lpt1" etc. The "type" command simply...
491
Benjamin
benjamin_y_75
Jul 24, 2006 7:03 am
Same story here. I have some additional information. If you delete and then redraw the "unconnected" wires, design rules says the problem is corrected. However...
492
John Carter
johnecarter
Jul 31, 2006 8:01 am
... back when ... believe that ... especially ... know if ... serial ... command codes ... it a ... information ... variants ... information to ... this ... ...
493
kierash@...
kierash@...
Jul 31, 2006 8:02 am
Hi everyone, a newbie here. just found tinycad and can honestly say its the easiest piece of cad software I've ever used, so far my only question is regarding...
494
Jon Chandler
jon_bainbridge
Jul 31, 2006 5:18 pm
... I've used Winline with a large HP plotter (7825 or some such) with good results. Never tried it with Tinycad, but it works well with Visio....at least the...
495
riderippey
rh@...
Aug 2, 2006 8:26 am
Hi all, I've been playing with TC for a while now, but this is the first time on the forum group. My copy keep 'spontaeously' duplicating parts after I've put...
496
markwayne
marcuswaynus
Aug 2, 2006 2:03 pm
I havnt seen this one. Check to see if you have any mouse utilitys on, like sticky focus or sticky clicking. Look through your mouse options and make sure...
497
ben@...
benjamin_y_75
Aug 2, 2006 4:09 pm
I have seen what you're describing also. Not sure what causes it. _____ From: tinycad@... [mailto:tinycad@...] On Behalf Of...
498
jwkaiser
Aug 4, 2006 7:48 am
To Newbie from another one! I just found TinyCAD a few days ago and I agree with you. I've been looking for a free/inexpensive electronic CAD program for quite...
499
Jason Brearley
tygft67
Aug 6, 2006 3:33 pm
I have just recently got TinyCad and I have a question. I have already made my schematic. Now i want to export the netlist into a PCB layout tool. The one i'm...
500
markwayne
marcuswaynus
Aug 6, 2006 6:48 pm
I don't know the details of what Eagle expects but I do know what FreePCB expects and I bet its similar. In the symbol proprieties there is or you you can add...
501
marcuswaynus
Aug 6, 2006 9:29 pm
I might be doing something goofy or this might be a bug I have found...lucky me. On this part I made. turning on things in the pin propertys makes the pin snap...
502
Jason Brearley
tygft67
Aug 9, 2006 8:04 am
I have recently done my schematic and want to export it to a PCB layout editor. When i go to create my netlist it The output file format is either Protel,...
503
Nikolay Koldirkaev
open2000@...
Aug 9, 2006 2:22 pm
Hello, TinyCad users, I need nice example to make screenshot for my article about Open Source CAD programs for Winodows. TinyCad for Windows is one of the ...
504
Bob Gardner
bobg12546
Aug 10, 2006 2:03 am
Jason, You might want to try FreePCB. It's a great program, it's well supported by its author, it accepts net lists from TinyCAD, and on top of that it's...
